The best time for tree trimming or to prune your trees is during the dormant period, usually in late winter from November to March.
During the dormant period is the best time for tree trimming; usually in late winter from November to March. Dead or diseased branches should be removed as soon as possible. Pruning done during the dormant season tends to have an invigorating effect on tree growth. Pruning done during peak growth times tends to slow growth by removing leaves that manufacture nourishment. However, too much summer pruning can damage a tree. Pruning during the spring (post-dormancy) and fall (pre-dormancy) is generally the least desirable time as the plant is most vulnerable during those times.
Berries and tree fruits are pruned November until bloom; prune blooming ornamentals during and immediately after bloom.
When you cut away part of a plant, a wound is left, susceptible to pests and diseases. To avoid trouble, always prune so as to make small wounds, rather than large ones. Removing a bud or twig produces a smaller wound than waiting until it is a large limb! Rubbing off a sucker bud leaves a smaller wound than if you wait until it has a year’s growth or more.
The insurer of the tree-damaged house will usually take responsibility.
If a tree on your property falls and damages your neighbor’s house, your neighbor’s insurer is the most likely party to take responsibility. But this isn’t always so. Exactly whose insurance is responsible will vary depending on whether it’s an act of nature alone or if it was caused by your negligence.
Who Is Responsible
In general, a fallen tree is considered an act of nature that the neighbor’s insurer covers. The negligence issue comes into play if the tree was dying, and your neighbor raised concerns about the possibility of it falling over and you ignored those concerns. In this case, the repair burden falls on your liability coverage. Insurance Company, says a neighbor can prove that she raised concerns by sending you an official letter, prior to the tree falling, warning that you may be held liable for potential damage and sending a copy to her insurer. Without such evidence, it may be difficult for her to prove any negligence.
Knowing in advance the health and safety of your trees and having them properly taken care of on a regular basis will help prevent future liability issues.
Deciduous trees or trees that shed their leaves annually enter a dormant state during fall or winter to help them survive the lower temperatures and the lack of water. This is a very good time for winter pruning, also called dormant tree pruning and 90% of the pruning can be done during this time.
The deciduous trees are still alive during winter dormancy. However, with the exception of some root growth when soil temperatures are favorable, the rest of the tree conserves energy by stopping growth and generally waiting out for the cold season to pass.
To put things in contrast, evergreen can conserve water a lot better and never fully enter dormancy. For that reason, evergreens should be pruned during growth season and not during winter.
What Is Winter Pruning
Winter pruning is the process of removing branches, parts of a branch or stems of a deciduous tree during the cold season when the plan is dormant. Properly done dormant tree pruning encourages growth, can shape the plants at the beginning of their lifecycle and can also improve the overall health of the tree.
When is the Dormant Season?
Trees enter dormancy after they drop their leaves to conserve water and stop growth during the cold season. Generally, in the trees drop their leaves in mid-October, with some tree species such as oaks and beeches keeping their leaves for a little bit longer.
Other factors that trigger dormancy are shorter days/longer nights, the amount of rainfall and a drop in soil temperature.
Long, warm autumns are not necessarily good for the plants, since they can grow new leaves and stems that will be killed by a sudden freeze.
When Does The Dormant Season End
There is no exact date when trees stop being dormant. To complicate things, weather is very unpredictable and might put plants back in eco-dormancy, or dormancy during the time when a plant is ready for growth, but the temperature is still not high enough. In California this occurs mainly in our higher altitudes.
The trees keep track of chilling units, or the number of hours when the temperature is above freezing, with temperatures between 40 to 50 F encouraging the plant to exit dormancy the most.
How Tree Dormancy Works
One of the most important reasons for a tree entering dormancy is water management during freezing temperatures.
There are 2 main ways trees manage water during winter and each one comes with advantages and disadvantages.
The tree keeps water inside their cells, but lowers the freezing point of the water by mixing it with various minerals or hormones. This process, also called supercooling, has the disadvantage of not being to able to withstand very cold temperatures. Even if the freezing point has been lowered, it is sometimes not low enough.
Some trees push water and liquids to the space in-between cells, allowing the water to freeze without damaging those cells. This process also has its own disadvantages, mainly because the tree may become dehydrated.
Winter Pruning Advantages
There are quite a few advantages to winter pruning, and that is why experts recommend the vast majority of pruning to be done during this time.
Sap Activity Changes During Freezing Temperatures
Because of the way how the trees manage water during the winter, new cuts will not ‘bleed’ as much.
The Tree Is More Likely To Increase Its Health
Because of the low temperatures, certain tree diseases and insects that act as pests are less active. Fresh cuts are more likely to attract tree diseases and insects, but not when it is cold outside.
There Is Less Shock To The Tree
Because the tree is dormant, it is not exposed to as much stress as pruning outside dormancy.
You Can Easily Inspect The Tree
With the foliage out of the way, it is easier to see a lot of details such as:
If the tree has any structural issues
Identifying dead or diseased areas of the tree and removing them to improve health
Pruning outside of growth season can prevent the sprouting of weaker shoots and promote stronger growth during spring
Winter pruning helps to easily identify potentially competing parts of the tree or branches that might represent a safety risk. These parts can be strategically removed by a trained arborist.
You Can Fertilize The Tree At The Same Time
Fertilizing the tree during dormant season benefits the roots as opposed to growing weak shoots.
Dormant Tree Pruning Techniques
There are a few pruning techniques. Some are good and some are bad for the tree (such as tree topping).
Any pruning work should be done with a purpose in mind:
Safety
Tree health
Space management (such as trees that are too close to power lines)
Disease management
Pest control
Air flow
Getting more sunlight
Making sure the tree does not compete with other plants
Shaping the tree
During winter, there are two main strategies you can use to prune dormant trees.
Thinning
It is the process of cutting of a whole branch all the way to the main trunk or to its parent branch. It is used for disease and pest control, or to direct light and improve air flow.
Heading Back
It is the process of removing just part of a branch. There can be no stub left after heading back a branch, because it might rot and attract a host of diseases and insects. To ensure there is no stub left, the branch has to be cut all the way to the next extending side branch or to the next bud.
Winter Pruning Services
So, should you prune your trees exclusively during winter? Not exactly. There are a lot of good reasons to prune trees during spring and summer:
Some species should be pruned in spring, after they are done blooming
To increase safety – some pruning cannot wait such as when the tree poses a safety risk to you and your property
Some minimal pruning to increase the beauty of the tree
To remove overhanging branches or to make room for something else
As you can see, there are a lot of factors that you have to take into consideration during a winter tree pruning project. The decisions you make will affect the overall health of the tree, it’s structural integrity and the way it will grow in the future. Trees increase your property’s value and healthy trees pose a much lower risk to its safety. That is why it is always a good idea to contact Flintridge Tree Care and our arborist for dormant tree pruning services.
The insurer of the tree-damaged house will usually take responsibility.
If a tree on your property falls and damages your neighbor’s house, your neighbor’s insurer is the most likely party to take responsibility. But this isn’t always so. Exactly whose insurance is responsible will vary depending on whether it’s an act of nature alone or if it was caused by your negligence.
Who Is Responsible
In general, a fallen tree is considered an act of nature that the neighbor’s insurer covers. The negligence issue comes into play if the tree was dying, and your neighbor raised concerns about the possibility of it falling over and you ignored those concerns. In this case, the repair burden falls on your liability coverage. Insurance Company, says a neighbor can prove that she raised concerns by sending you an official letter, prior to the tree falling, warning that you may be held liable for potential damage and sending a copy to her insurer. Without such evidence, it may be difficult for her to prove any negligence.
Knowing in advance the health and safety of your trees and having them properly taken care of on a regular basis will help prevent future liability issues.
A properly pruned tree looks as natural as possible; the tree’s appearance reflects its fundamental form and character. The pruner must maintain this structural integrity and know a little tree biology and proper pruning principles.
Recommended pruning equipment
Hand pruners (Felco or ARS type, bypass, not anvil type)
long-handled loppers, 18-inch (Corona type, bypass, not anvil type)
hand-saw, 12–16 inches
bottle of rubbing alcohol or 10:1 diluted bleach
whetting stone/sharpener
oil
file
safe ladder (3-legged are best for uneven ground)
pole pruner, 10-foot (optional)
chain saw (optional)
Tree Trimming Priorities
Maintain the health of the tree
remove all dead, dying, and diseased limbs
remove crossovers, which can rub together and damage limbs and harbor disease
remove hazardous branches before they fall
correct and repair damage.
Raise the canopy to increase pedestrian, vehicular or visual zone.
Rejuvenate the tree by the removal of old wood in such a way that encourages the formation of new wood (remove no more than 1/3 of the wood in one year).
Improve the aesthetic quality of the tree and, thus, its value.
Slow the tree’s growth by timely removal of foliage (but best to select the right plant for the site).
Fruit trees:
increase fruit production
develop strong 45-degree angles to support the fruit load
remove limbs that grow down or straight up
maintain tree size (5 to 10 feet is ideal size for a home orchard in terms of accessibility)
maintain fruit spurs.
When to prune trees
The best time to prune trees is during the dormant period, usually in late winter from November to March.
The best time to prune trees is during the dormant period, usually in late winter from November to March. Dead or diseased branches should be removed as soon as possible. Pruning done during the dormant season tends to have an invigorating effect on tree growth. Pruning done during peak growth times tends to slow growth by removing leaves that manufacture nourishment. However, too much summer pruning can damage a tree. Pruning during the spring (post-dormancy) and fall (pre-dormancy) is generally the least desirable time as the plant is most vulnerable during those times.
Berries and tree fruits are pruned November until bloom; prune blooming ornamentals during and immediately after bloom.
When you cut away part of a plant, a wound is left, susceptible to pests and diseases. To avoid trouble, always prune so as to make small wounds, rather than large ones. Removing a bud or twig produces a smaller wound than waiting until it is a large limb! Rubbing off a sucker bud leaves a smaller wound than if you wait until it has a year’s growth or more.
Pruning cuts
Heading vs. thinning cuts
A tree’s response to a pruning cut depends on where on the branch the cut is made. Both types of cuts are used in pruning fruit trees and grapes.
Heading cuts: Several buds left on the cut branch grow, making denser, more compact foliage on more branches. (Figure 1)
Thinning cuts: Branches are removed entirely, leaving no buds to grow. Their energy is diverted into remaining branches, which grow more vigorously. (Figure 2)
Angle and placement of cuts
Always make cuts close to a node. Branches grow only at these nodes, and if you leave too long a stub beyond the node, the stub will die and rot. (Figure 3)
Prune to the lateral bud that will produce the branch you want. The placement of that bud on the stem points the direction of the new branch. An outside bud, pruned with a slanting cut just above the bud, will usually produce an outside branch. A flat cut above the bud allows two lower buds to release and grow shots.
Pruning thick, heavy branches
Undercut the bottom of the branch about a third of the way through, 6–12 inches out from the trunk. (Figure 4, a)
Make a second cut from the top, about 2-inches farther out from the under-cut, until the branch falls away. (Figure 4, b)
Cut back the resulting stub to the branch collar, not flush with the trunk. (Figure 4, c)
Anatomy of a fruit tree
Crotch: The angle where branches fork, or where a main limb joins the trunk. Strong crotches are wide-angled, 45 degrees; weak crotches are narrow.
Scaffold: The main limbs branching from the trunk.
Watersprout: A very vigorous shoot from a dormant bud on a branch. Remove by cutting.
Sucker: A vigorous shoot from the roots or from below the bud union. Cut off at the base. (To remove, dig out soil around sucker, clip the sucker off and leave cut exposed to air.)
Parts of the branch
Terminal bud: The fat bud at a branch tip will always grow first and fastest if you leave it. Cut it, and several buds will grow behind it.
Leaf bud: Flattish triangle on the side of a branch. To make one grow, cut just above it. Choose buds pointing outward from the trunk so the growing branch will have space and light.
Flower bud: Plump compared to leaf buds and first to swell in spring. On stone fruits they grow alone or beside leaf buds. On apples and pears they grow with a few leaves.
Spur: A short twig on apples, pears, plums, and apricots that grow on older branches, produce fat flower buds, then fruit. Don’t remove them.
Bud scar: A ring on a branch that marks the point where the terminal bud began growing after the dormant season. The line marks the origin of this year’s growth.
Types of tree forms
Central leader: one dominant trunk all the way to the top; strong, good light penetration; difficult to reach higher branches with large trees
Modified central leader: central leader trunk to 6 to 10 feet, then multiple leader; combines strength of central trunk with sun-filled center of a vase shape
Vase shape or multiple leaders: vase shape with many branches; the short trunk of about 3 feet with three or four main limbs, each of which has fully filled-out secondary branches, creating an open center allowing light to reach all branches
Others: include espalier and trellis
Training for a vase shape
First dormant season: After the tree has grown through the spring, summer, and fall and into its first winter dormancy, choose three or four branches with wide (45-degree) crotches, looking for branches that radiate evenly around the trunk. Try to have at least 6 inches vertical distance between branches, with the lowest branch about 15–18 inches above the ground. Cut off the vertical stem just above the top one. (If there are fewer than three good branches, head cut the vertical stem and choose the remaining scaffold branches during the next dormant season.)
Second dormant season: If necessary, choose the remaining scaffold branches and cut off the vertical stem just above the highest selected scaffold branch. Remove the weakest side branches from the scaffold branches chosen last season, leaving the main stem and laterals on each branch.
Third dormant season: Now is the time to thin surplus shoots and branches. Select the strongest and best-placed terminal shoot near the tip of each scaffold branch, as well as four to six other side shoots on each scaffold (branch). Leave the short weak shoots that grow straight from the trunk, to shade it and help produce food for the tree.
Frequently asked questions
Should I remove my big old apple tree?
Keep it if it has sentimental value, produces good fruit, shades the house, houses a swing or treehouse for the kids. Otherwise, remove it and replace it with several dwarf or semi-dwarf fruit trees. The ideal tree for the home orchard is 5–10 feet; at that height, you are best able to prune, spray, thin and harvest.
Is it okay to prune suckers and watersprouts? When and how do I do it?
Such overly vigorous growth can be controlled by early summer pruning, which discourages them from regrowing; cut them off at the base. Better yet, rub them off with your thumb in May or June. Watersprouts will emerge following an overzealous dormant season pruning job; sometimes it’s best to leave one or two of these, particularly as a replacement for the leader if it was cut, to discourage regrowth of the others.
Do I need to paint the wounds with a sealing compound?
No, this is no longer recommended. The tree or plant is best protected by proper pruning technique and timing. Sealing compounds encourage wood rot.
How can I slow the growth of a tree?
It is always best to select the right tree for the site, rather than try to work against nature. However, these techniques will help to retard the growth of a tree:
Reduce dormant pruning and prune more in June or July. (Winter pruning invigorates a tree; summer pruning decreases vigor and size.)
Give no or less nitrogen. Give less water.
Hand pull the water suckers in May or June, when they are 2–4 inches long and flexible; this makes it less likely they will regrow. (Pruning suckers in the winter ensures they will regrow in the spring.) Leave a sucker on top of the tree to dominate, called apical dominance.
Should I prune a fruit tree when I plant it?
In digging up a young tree from the nursery, some of the root system can be damaged; top pruning is usually required to prevent tree stress due to the lack of balance between the root system and the top. However, excessive pruning of young trees may delay blossoming and fruiting.
For a single whip, prune tree to waist height at planting. Branching will begin at this pruning cut.
DECIDUOUS TREE TRIMMING
Most deciduous trees should be pruned during their dormant period after leaves have fallen, which is usually October, November, December or January. Such trees include:
* Ash (Fraxinus species)
* Birch (Betula species)
* Cape chestnut (Calodendrum capense)
* Chinese elm (Ulmus parvifolia)
* Chinese pistache (Pistacia chinensis)
* Fruitless mulberry (Morus alba)
* Ginkgo (Ginkgo biloba)
* Italian alder (Alnus cordata)
* Maple
* Sweet gum (Liquidambar styraciflua)
For Expert Tree Trimming click the “Find out More” button!Find out more
FLOWERING TREE TRIMMING
Prune flowering trees when they are dormant, if they are deciduous, or immediately after flowering is completed, if they are evergreen. For those trees that bloom when they are leafless, in most cases.
* Acacias (various species)
* Bradford pear (Pyrus calleryana, several cultivars), which blooms while leafless
* Camellia Japonica
* Cape chestnut (Calodendrum capense)
* Cassia
* Chinese flame tree (Koelreuteria bipinnata)
* Coral trees (Erythrina caffra and other species), which bloom while leafless
* Crape myrtle
* Empress tree (Paulownia tomentosa), which blooms while leafless
* Firewheel trees (Stenocarpus sinuatus)
* Jacaranda
* Lemon bottlebrush (Callistemon citrinus)
* New Zealand Christmas tree
* Purple orchid tree (Bauhinia variegata)
* Saucer magnolia (Magnolia soulangiana), which blooms while leafless
* Silk tree/mimosa ( Albizia julibrissin)
* Southern magnolia (Magnolia grandiflora)
* Tipu tree (Tipuana tipu)
For Expert Tree Trimming click the “Find out More” button!Find out more
FALL & WINTER TREE TRIMMING GUIDE
BROAD-LEAF EVERGREENS TREE TRIMMING
Broadleaf evergreens should be pruned
October, through March or May or June.
Such trees include:
* Bronze loquat (Eriobotrya deflexa)
* Camphor tree (Cinnamomum camphora)
* Carrot wood (Cupaniopsis anacardioides)
* Eucalyptus species
* Kaffir plum (Harpephyllum caffrum)
* Olive (Olea europaea)
* Ornamental figs (ficus species)
* Peppermint tree (Agonis flexuosa)
* Pittosporum species, such as Victorian box (Pittosporum undulatum)
* Toyon (Heteromeles arbutifolia)
For Expert Tree Trimming click the “Find out More” button!Find out more
